Chip Common Mode Choke (CM series CMH05MT300)

Chip Common Mode Choke (CM series CMH05MT300) / Viking Tech has the experience in the design of innovative components, offering support and service to Global customers that demand a genuine manufacturing partner. Our goal is to be the leader in design, manufacturing, and marketing of miniature, precision passive components used throughout Automotive, Industrial and 3C electronic applications.

Chip Common Mode Choke (CM series CMH05MT300)

CMH05MT300

Chip Common Mode Choke (CM series CMH05MT300)
Chip Common Mode Choke (CM series CMH05MT300) Files Download

Chip common mode Filter is small chip inductor with ferrite core and two line types wire wounded. Highly effective in noise suppression high common mode impedance at noise band and low differential mode impedance at signal band , low differential mode impedance with high coupling factor. there is almost no distortion on high speed singal. tipically for EMI radiation noise suppression for any electronic devices.
CM Series0805 ±20% 30μH 0.2 Ω 450mA 125V 10MΩ min.

SizeToleranceInductanceTest ConditionDCR (Ω) max.IDC (mA)Rated VoltageWithstanding Voltage Vdc (V)Insulation Resistance (MΩ) min.
0805±20%30100MHz0.24505012510

Environmental Characteristics

Electrical Performance Test

ItemsRequirementTest Conditions / Test Methods
ImpedanceRefer to standard electrical
characteristic spec.
Component should not be damaged
LCR Meter HP 4291B
DC Resistance DCRMicro-Ohm meter (GOM-801G)
Withstand Voltage (VDC)Test Voltage: 2.5 Times Rated Voltage
Testing Time: 60 seconds
Charge Current: 0.5mA
Rated Voltage (VDC)Test Voltage: Rated Voltage
Testing Time: 1 to 5 seconds
Charge Current: 1mA
Insulation Resistance (I.R)Charge Current: 1minute
10M ohm min.

Mechanical Performance Test

ItemsRequirementTest Conditions / Test Methods
Component Adhesion
(Push Test)
Base: 0805≧2 Lbs
Cover: 0805≧1 Lbs
Base: 1206≧4 Lbs
Cover: 1206≧2 Lbs
The component should be soldered (232°C± 5°C for 10 sec.) to tinned copper substrate
Applied force gauge to the side of component It must withstand   force of 2 or 4 pounds without failure of the component.
DropComponent should not be damagedDropping chip by each side and corner. Drop 10 times in total
Drop height: 100 cm
Drop weight: 125 g
SolderabilityThe terminal should at least be 90% covered with solderThe component shall be dipped in a melted solder bath at 245 ±5 for 3 seconds
Vibration Test (Low Frequency)Component should not be damaged1. Amplitude: 1.5 m/m
2. Frequency: 10-55-10Hz (1min.)
3. Direction: X, Y, Z
4. Duration: 2 Hrs/X, Y, Z

Climatic Test

ItemsRequirementTest Conditions / Test Methods
Low Temperature StorageImpedance change: Within± 20%
Without distinct damage in appearance
1. Temp: -40 ±2°C
2. Time: 1000±48 Hours
3. Component should be tested after 1hour at room temperature
Thermal Shock
Total: 5 Cycles
High Temperature Storage1. Temp: 85 ± 2°C
2. Time: 1000 ± 48 Hours
3. Component should be tested after 1hour at room temperature
Humidity1. Temp: 40 ± 2°C
2. R.H. : 90 ~ 95%
3. Time: 48 ±2 Hours
High Temperature Load LifeThere should be no evidence of short or open circuit1. Temp: 85 ± 2°C
2. Time: 96 ± 12 Hours
3. Load: Allowed DC Current
Low Temperature Load Life1. Temp: -40 ± 2°C
2. Time: 96 ± 12 Hours
3. Load: Allowed DC Current
☑ Storage Temperature: 15~28°C; Humidity < 80%RH

Packaging

Packaging Quantity & Reel Specifications

Packing Quantity & Reel Specifications
TypeΦAΦBΦCWTQuantity (EA)
CMH05178±2.060±0.513±0.39±0.311.4±1.02000
CMH06178±2.060±0.513±0.39±0.311.4±1.02000

Embossed Plastic Tape Specifications

Emboss Plastic Tape Specifications
TypeA (mm)B (mm)W (mm)E (mm)F (mm)P0 (mm)P1 (mm)P2 (mm)ΦD0 (mm)T (mm)
CMH051.40±0.102.55±0.058.0±0.201.75±0.103.5±0.104.00±0.104.00±0.102.00±0.101.50+0.101.35±0.10
CMH061.90±0.103.50±0.058.0±0.201.75±0.103.5±0.104.00±0.104.00±0.102.00±0.101.50+0.102.10±0.10

Peel-off Force

The force for tearing off cover tape is 0.05~0.69 (N) in the arrow direction at the following conditions:
Temperature: 5 ~ 35°C
Humidity: 45 ~ 85%
Atmospheric pressure: 860 ~ 1060hpa

Peel-off Force
Files Download


SEARCH

Condition search:      Cross Search

Menu

Best Sale

Chip Common Mode Choke (CM series CMH05MT300) Manufacturer - Viking

Based in Taiwan, Viking Tech Corporation is one of the prime Chip Common Mode Choke (CM series CMH05MT300) manufacturers since 1997. And their products are used throughout automotive, electronic device applications, with manufacturing tolerance down to 0.01% and TCR down to 2 ppm in a broad range of package sizes.

TS16949/ ISO9001/ ISO14001 and meet AEC-Q200 standards, Viking has been offering anti-sulfur, anti-surge, pulse, high voltage, high power precision resistors including thin/ thick film resistors, automotive resistors, melf resistors, current sense resistors, etc. Low noise, low TC, high power inductors such as rf inductors, chip inductors, power inductors, variable inductors, ferrite chip inductors, shielded inductors, wire wound inductors and dip inductors.

Chip Common Mode Choke (CM series CMH05MT300) has been offering customers high quality power resistors, power inductors and aluminum electrolytic capacitors with solid reputation. Both with advanced technology and 25 years of experience, Viking makes sure to meet each customer's demands.

Chip Common Mode Choke (CM series CMH05MT300) has been offering customers high quality power resistors, power inductors and aluminum electrolytic capacitors with solid reputation. Both with advanced technology and 25 years of experience, Viking makes sure to meet each customer's demands.


Main Product

AUTOMOTIVE APPLICATIONS

AUTOMOTIVE APPLICATIONS

Thin film Precision resistor 0.01%, TC2ppm, wirebondale, Anti-Crossive, MELF. Current sensing, Metal...

Read More
MEDICAL APPLICATIONS

MEDICAL APPLICATIONS

Ceramic high frequency chip inductors, small size to 01005. Thin film, multilayer, wirewound , ferrite...

Read More
COMMUNICATION APPLICATIONS

COMMUNICATION APPLICATIONS

Multilayer Ceramic capacitor offers high Voltage, high frequency, low noise, High Q, Low TCR. NPO, X7R,...

Read More