Chip Common Mode Choke (CM series CMH06MT261)

Chip Common Mode Choke (CM series CMH06MT261)

CMH06MT261

Chip Common Mode Choke (CM series CMH06MT261)
Chip Common Mode Choke (CM series CMH06MT261) Files Download

Chip common mode Filter is small chip inductor with ferrite core and two line types wire wounded. Highly effective in noise suppression high common mode impedance at noise band and low differential mode impedance at signal band , low differential mode impedance with high coupling factor. there is almost no distortion on high speed singal. tipically for EMI radiation noise suppression for any electronic devices.
CM Series1206 ±20% 260μH 0.5 Ω 310mA 125V 10MΩ min.

SizeToleranceInductance (μH)Test ConditionDCR (Ω) max.IDC (mA)Rated VoltageWithstanding Voltage Vdc (V)Insulation Resistance (MΩ) min.
1206±20%260100MHz0.53105012510

Environmental Characteristics

Electrical Performance Test

Items Requirement Test Conditions / Test Methods
Impedance Refer to standard electrical
characteristic spec.
Component should not be damaged
LCR Meter HP 4291B
DC Resistance DCR Micro-Ohm meter (GOM-801G)
Withstand Voltage (VDC) Test Voltage: 2.5 Times Rated Voltage
Testing Time: 60 seconds
Charge Current: 0.5mA
Rated Voltage (VDC) Test Voltage: Rated Voltage
Testing Time: 1 to 5 seconds
Charge Current: 1mA
Insulation Resistance (I.R) Charge Current: 1minute
10M ohm min.

Mechanical Performance Test

Items Requirement Test Conditions / Test Methods
Component Adhesion
(Push Test)
Base: 0805≧2 Lbs
Cover: 0805≧1 Lbs
Base: 1206≧4 Lbs
Cover: 1206≧2 Lbs
The component should be soldered (232°C± 5°C for 10 sec.) to tinned copper substrate
Applied force gauge to the side of component It must withstand   force of 2 or 4 pounds without failure of the component.
Drop Component should not be damaged Dropping chip by each side and corner. Drop 10 times in total
Drop height: 100 cm
Drop weight: 125 g
Solderability The terminal should at least be 90% covered with solder The component shall be dipped in a melted solder bath at 245 ±5 for 3 seconds
Vibration Test (Low Frequency) Component should not be damaged 1. Amplitude: 1.5 m/m
2. Frequency: 10-55-10Hz (1min.)
3. Direction: X, Y, Z
4. Duration: 2 Hrs/X, Y, Z

Climatic Test

Items Requirement Test Conditions / Test Methods
Low Temperature Storage Impedance change: Within± 20%
Without distinct damage in appearance
1. Temp: -40 ±2°C
2. Time: 1000±48 Hours
3. Component should be tested after 1hour at room temperature
Thermal Shock
Total: 5 Cycles
High Temperature Storage 1. Temp: 85 ± 2°C
2. Time: 1000 ± 48 Hours
3. Component should be tested after 1hour at room temperature
Humidity 1. Temp: 40 ± 2°C
2. R.H. : 90 ~ 95%
3. Time: 48 ±2 Hours
High Temperature Load Life There should be no evidence of short or open circuit 1. Temp: 85 ± 2°C
2. Time: 96 ± 12 Hours
3. Load: Allowed DC Current
Low Temperature Load Life 1. Temp: -40 ± 2°C
2. Time: 96 ± 12 Hours
3. Load: Allowed DC Current
☑ Storage Temperature: 15~28°C; Humidity < 80%RH

Packaging

Packaging Quantity & Reel Specifications

Packing Quantity & Reel Specifications
Type ΦA ΦB ΦC W T Quantity (EA)
CMH05 178±2.0 60±0.5 13±0.3 9±0.3 11.4±1.0 2000
CMH06 178±2.0 60±0.5 13±0.3 9±0.3 11.4±1.0 2000

Embossed Plastic Tape Specifications

Emboss Plastic Tape Specifications
Type A (mm) B (mm) W (mm) E (mm) F (mm) P0 (mm) P1 (mm) P2 (mm) ΦD0 (mm) T (mm)
CMH05 1.40±0.10 2.55±0.05 8.0±0.20 1.75±0.10 3.5±0.10 4.00±0.10 4.00±0.10 2.00±0.10 1.50+0.10 1.35±0.10
CMH06 1.90±0.10 3.50±0.05 8.0±0.20 1.75±0.10 3.5±0.10 4.00±0.10 4.00±0.10 2.00±0.10 1.50+0.10 2.10±0.10

Peel-off Force

The force for tearing off cover tape is 0.05~0.69 (N) in the arrow direction at the following conditions:
Temperature: 5 ~ 35°C
Humidity: 45 ~ 85%
Atmospheric pressure: 860 ~ 1060hpa

Peel-off Force
Files Download


SEARCH

Condition search:      Cross Search

Best Sale

Chip Common Mode Choke (CM series CMH06MT261) Manufacturer - Viking

Based in Taiwan, Viking Tech Corporation is one of the prime Chip Common Mode Choke (CM series CMH06MT261) manufacturers since 1997. And their products are used throughout automotive, electronic device applications.

TS16949/ ISO9001/ ISO14001 and meet AEC-Q200 standards, Viking has been offering anti-sulfur, anti-surge, pulse, high voltage, high power precision resistors including thin/ thick film resistors, automotive resistors, melf resistors, current sense resistors, etc. Low noise, low TC, high power inductors such as rf inductors, chip inductors, power inductors, variable inductors, ferrite chip inductors, shielded inductors, wire wound inductors and dip inductors.

Viking has been offering customers high quality power resistors, power inductors and aluminum electrolytic capacitors with solid reputation. Both with advanced technology and 20 years of experience, Viking makes sure to meet each customer's demands.


Hot Products

Resistor

Resistor

Thin film Precision resistor 0.01%, TC2ppm, wirebondale, Anti-Crossive, MELF. Current sensing, Metal...

Read More
Inductor

Inductor

Ceramic high frequency chip inductors, small size to 01005. Thin film, multilayer, wirewound , ferrite...

Read More
Capacitor

Capacitor

Multilayer Ceramic capacitor offers high Voltage, high frequency, low noise, High Q, Low TCR. NPO, X7R,...

Read More