Draadgewonden type vermogensinductor

'VIKING TECH' heeft ervaring in het ontwerpen van innovatieve componenten en biedt ondersteuning en service aan wereldwijde klanten die een betrouwbare productiepartner eisen. Ons doel is om leider te zijn in het ontwerpen, produceren en vermarkten van miniatuur, precisie passieve componenten die worden gebruikt in de automobiel-, industriële en 3C-elektronica-toepassingen.

Draadgewonden type vermogensinductor

MLP04MTR33

Draadgewonden type vermogensinductor
Draadgewonden type vermogensinductor Files Download

Draadgewonden ferrite chip hoogvermogen inductor, kleine afmetingen, gesloten magnetisch circuit voorkomt overspraak, geschikt voor installatie met hoge dichtheid en reflow solderen. Gebruikt in allerlei elektronische apparaten, computers, converters.
MLP Series1004 ±20% 0.33μH 0.026 Ω 6A 4A

GrootteTolerantieInductieTestconditieDCR (Ω) max.I sat (A) max.I rms (A) max.
1004±20%0.331MHz, 1mA0.02664

Specificaties voor hoge stroom elektrisch

MLPH06 (0806) Wire Wound Type Power Inductor

Codes Inductance (uH) Tolerance Test Condition DCR (mΩ) max. Isat (A) max. Irms (A) max.
R47 0.47 ± 20% 1MHz, 1V 30 5.30 4.05
1R0 1.0 ± 20% 1MHz, 1V 60 3.30 3.00
1R5 1.5 ± 20% 1MHz, 1V 99 3.10 2.20
2R2 2.2 ± 20% 1MHz, 1V 140 2.45 2.00

MLPH04 (1004) Wire Wound Type Power Inductor

R47 0.47 ± 20% 1MHz, 1V 29 6.00 4.40
1R0 1.0 ± 20% 1MHz, 1V 52 4.00 3.10
2R2 2.2 ± 20% 1MHz, 1V 110 3.00 2.10

MLPH08 (1008) Wire Wound Type Power Inductor

Codes Inductance (uH) Tolerance Test Condition DCR (mΩ) max. Isat (A) max. Irms (A) max.
R47 0.47 ± 20% 1MHz, 1V 22 6.20 4.90
1R0 1.0 ± 20% 1MHz, 1V 44 4.30 3.30
2R2 2.2 ± 20% 1MHz, 1V 89 3.20 2.20

Operating Temperature range: -40°C to +125°C

Milieukarakteristieken

Electrical Performance Test

Item Requirement Test Method
Inductance Refer to standard electrical characteristic spec. HP4285A
DC Resistance RDC micro-ohm meter.
Isat DC current will cause a 30% inductance reduction form initial value.
Irms DC current will cause coil temp. rising to 40℃ whichever is smaller.

Mechanical Performance Test

Item Requirement Test Method
Resistance to Soldering Heat Appearance: No damage
More than 95% of the terminal.
Electrode should be covered with solder.
Inductance: within ± 20% of initial value
Flux: Rosin
Solder Temperature: 260 ± 5°C
Immersion Time: 10 ± 1 sec.
Adhesive Test No mechanical damage
Soldering the products on PCB after the pulling test force>5N
Reflow temperature: 245°C it shall be soldered on the substrate applying direction parallel to the substrate
Apply force(F): 5 N
Test time: 10 sec
Temperature Cycle No mechanical damage
Inductance: within ± 20% of initial value
Temperature: -50 ~ 125°C for 30 minutes each
Cycle: 500cycles
Measurement: at ambient temperature 24 hours after test completion
Dry Heat Test Temperature: 85 ± 2°C
Testing time: 500 hrs
Applied current: full rated current
Measurement: at ambient temperature 24 hours after test completion
Humidity Test Temperature: 60 ± 2°C, Humidity: 90 ~ 95% RH
Testing time: 500 hrs
Applied current: full rated current
Measurement: at ambient temperature 24 hours after test completion

☑Storage Temperature: 5~40°C ; Humidity:<65%RH

Terugvloeien

Recommendable Reflow Soldering

Recommendable Reflow Soldering

Verpakking

Reel Specifications (Unit: mm)

Type A B C W T Quantity (EA) Reel Specifications - MLP
MLP03 178 ± 1 60.0 + 0.5 13.0 ± 0.2 9.00 ± 0.5 12.0 ± 0.15 3,000
MLP05 178 ± 1 60.0 + 0.5 13.0 ± 0.2 9.00 ± 0.5 12.0 ± 0.15 3,000
MLP(H)06 178 ± 1 60.0 + 0.5 13.0 ± 0.2 9.00 ± 0.5 12.0 ± 0.15 3,000
MLP(H)04 178 ± 1 60.0 + 0.5 13.0 ± 0.2 9.00 ± 0.5 12.0 ± 0.15 3,000
MLP(H)08 178 ± 1 60.0 + 0.5 13.0 ± 0.2 9.00 ± 0.5 12.0 ± 0.15 3,000
MLP10 178 ± 1 60.0 + 0.5 13.0 ± 0.2 9.00 ± 0.5 12.0 ± 0.15 3,000

Tape Specifications (Unit: mm)

Type A0 B0 K0 t Tape Specifications - MLP
MLP03 1.45 ± 0.10 2.20 ± 0.10 1.12 ± 0.10 0.22 ± 0.05
MLP05 1.45 ± 0.10 2.20 ± 0.10 1.12 ± 0.10 0.22 ± 0.05
MLP06 1.80 ± 0.10 2.20 ± 0.10 1.15 ± 0.10 0.22 ± 0.05
MLPH06 1.82 ± 0.05 2.23 ± 0.05 1.15 ± 0.05 0.22 ± 0.05
MLP04 2.50 ± 0.10 3.00 ± 0.10 1.60 ± 0.10 0.25 ± 0.05
MLPH04 2.25 ± 0.05 2.80 ± 0.10 1.35 ± 0.10 0.22 ± 0.05
MLP08 2.50 ± 0.10 3.00 ± 0.10 1.60 ± 0.10 0.25 ± 0.05
MLPH08 2.25 ± 0.05 2.80 ± 0.10 1.35 ± 0.10 0.22 ± 0.05
MLP10 2.80 ± 0.10 3.45 ± 0.10 1.34 ± 0.10 0.23 ± 0.05

Code

  • R33
Bestanden Downloaden


ZOEKEN

Voorwaarde zoeken:      Kruis zoeken

Menu

Beste verkoop

Viking Introduction

Viking Tech Corporation is Taiwan supplier and manufacturer in Gecertificeerde RF-spoelleverancier Viking has been offering our customers high quality Dunne film precisie weerstand, stroomdetectieweerstand, RF-keramische chip-inductor, vermogensinductor, MELF dunne film weerstand, dikke film weerstand, MLCC, Multilayer chip-condensator, Chip-kraal, vermogensweerstand, Anti-zwavel weerstand, hoogspanningsweerstand, Anti-surge weerstand, anti-puls weerstand. Weerstandsmatrix, doorvoerweerstand, Aluminium vaste elektrolytische condensator since 1997. With both advanced technology and 25 years experience, Viking always make sure to meet each customer's demand.


Hoofdproduct

AUTOMOTIVE TOEPASSINGEN

AUTOMOTIVE TOEPASSINGEN

Dunne film precisieweerstand 0,01%, TC2ppm, wirebondale, Anti-Crossive, MELF. Stroomsensing, Metaal,...

Lees verder
MEDISCHE TOEPASSINGEN

MEDISCHE TOEPASSINGEN

Keramische hoogfrequente chip-inductoren, kleine afmeting tot 01005. Dunne film, meerlaags, draadgewonden,...

Lees verder
COMMUNICATIETOEPASSINGEN

COMMUNICATIETOEPASSINGEN

Meerlagige keramische condensator biedt hoge spanning, hoge frequentie, laag ruis, hoge Q, lage TCR....

Lees verder