Wire Wound Type Power Inductor

Wire Wound Type Power Inductor

MLP04MTR47

Wire Wound Type Power Inductor
Wire Wound Type Power Inductor Files Download

Wirewound ferrite chip high power inductor , small sizes , closed magnetic circuit avoids crosstalk , suitable for high density installation and re-flow soldering. Used in all kind electronic devices, computing, converters.
MLP Series1004 ±20% 0.47μH 0.032 Ω 4.5A 3.51A

SizeToleranceInductance (μH)Test ConditionDCR (Ω) max.I sat (A) max.I rms (A) max.
1004±20%0.471MHz, 1mA0.0324.53.51

High Current Electrical Specifications

MLPH06 (0806) Wire Wound Type Power Inductor

CodesInductance (uH)ToleranceTest ConditionDCR (mΩ) max.Isat (A) max.Irms (A) max.
R470.47± 20%1MHz, 1V305.304.05
1R01.0± 20%1MHz, 1V603.303.00
1R51.5± 20%1MHz, 1V993.102.20
2R22.2± 20%1MHz, 1V1402.452.00

MLPH04 (1004) Wire Wound Type Power Inductor

CodesInductance (uH)ToleranceTest ConditionDCR (mΩ) max.Isat (A) max.Irms (A) max.
R330.33± 20%1MHz, 1V227.004.80
R470.47± 20%1MHz, 1V296.004.40
1R01.0± 20%1MHz, 1V524.003.10
2R22.2± 20%1MHz, 1V1103.002.10

MLPH08 (1008) Wire Wound Type Power Inductor

CodesInductance (uH)ToleranceTest ConditionDCR (mΩ) max.Isat (A) max.Irms (A) max.
R470.47± 20%1MHz, 1V226.204.90
1R01.0± 20%1MHz, 1V444.303.30
2R22.2± 20%1MHz, 1V893.202.20

Operating Temperature range: -40°C to +125°C

Environmental Characteristics

Electrical Performance Test

ItemRequirementTest Method
InductanceRefer to standard electrical characteristic spec.HP4285A
DC Resistance RDCmicro-ohm meter.
IsatDC current will cause a 30% inductance reduction form initial value.
IrmsDC current will cause coil temp. rising to 40℃ whichever is smaller.

Mechanical Performance Test

ItemRequirementTest Method
Resistance to Soldering HeatAppearance: No damage
More than 95% of the terminal.
Electrode should be covered with solder.
Inductance: within ± 20% of initial value
Flux: Rosin
Solder Temperature: 260 ± 5°C
Immersion Time: 10 ± 1 sec.
Adhesive TestNo mechanical damage
Soldering the products on PCB after the pulling test force>5N
Reflow temperature: 245°C it shall be soldered on the substrate applying direction parallel to the substrate
Apply force(F): 5 N
Test time: 10 sec
Temperature CycleNo mechanical damage
Inductance: within ± 20% of initial value
Temperature: -50 ~ 125°C for 30 minutes each
Cycle: 500cycles
Measurement: at ambient temperature 24 hours after test completion
Dry Heat TestTemperature: 85 ± 2°C
Testing time: 500 hrs
Applied current: full rated current
Measurement: at ambient temperature 24 hours after test completion
Humidity TestTemperature: 60 ± 2°C, Humidity: 90 ~ 95% RH
Testing time: 500 hrs
Applied current: full rated current
Measurement: at ambient temperature 24 hours after test completion

Reflow

Recommendable Reflow Soldering

Recommendable Reflow Soldering

Packaging

Reel Specifications (Unit: mm)

TypeABCWTQuantity (EA)Reel Specifications - MLP
MLP(H)06178 ± 160.0 + 0.513.0 ± 0.29.00 ± 0.512.0 ± 0.53,000
MLP(H)04178 ± 160.0 + 0.513.0 ± 0.29.00 ± 0.512.0 ± 0.53,000
MLP(H)08178 ± 160.0 + 0.513.0 ± 0.29.00 ± 0.512.0 ± 0.53,000

Tape Specifications (Unit: mm)

TypeA0B0K0tTape Specifications - MLP
MLP061.80 ± 0.102.20 ± 0.101.15 ± 0.100.22 ± 0.05
MLPH061.82 ± 0.052.23 ± 0.051.15 ± 0.050.22 ± 0.05
MLP042.50 ± 0.103.00 ± 0.101.60 ± 0.100.25 ± 0.05
MLPH042.25 ± 0.052.80 ± 0.101.35 ± 0.100.22 ± 0.05
MLP082.50 ± 0.103.00 ± 0.101.60 ± 0.100.25 ± 0.05
MLPH082.25 ± 0.052.80 ± 0.101.35 ± 0.100.22 ± 0.05

Code

  • R47
Files Download


SEARCH

Condition search:      Cross Search

Best Sale

Wire Wound Type Power Inductor Manufacturer - Viking

Based in Taiwan, Viking Tech Corporation is one of the prime Wire Wound Type Power Inductor manufacturers since 1997. And their products are used throughout automotive, electronic device applications.

TS16949/ ISO9001/ ISO14001 and meet AEC-Q200 standards, Viking has been offering anti-sulfur, anti-surge, pulse, high voltage, high power precision resistors including thin/ thick film resistors, automotive resistors, melf resistors, current sense resistors, etc. Low noise, low TC, high power inductors such as rf inductors, chip inductors, power inductors, variable inductors, ferrite chip inductors, shielded inductors, wire wound inductors and dip inductors.

Viking has been offering customers high quality power resistors, power inductors and aluminum electrolytic capacitors with solid reputation. Both with advanced technology and 20 years of experience, Viking makes sure to meet each customer's demands.


Hot Products

Resistor

Resistor

Thin film Precision resistor 0.01%, TC2ppm, wirebondale, Anti-Crossive, MELF. Current sensing, Metal...

Read More
Inductor

Inductor

Ceramic high frequency chip inductors, small size to 01005. Thin film, multilayer, wirewound , ferrite...

Read More
Capacitor

Capacitor

Multilayer Ceramic capacitor offers high Voltage, high frequency, low noise, High Q, Low TCR. NPO, X7R,...

Read More